Lenovo ThinkSystem NE0152T Installation Manual Download Page 108

Page: 108 / 110

108

NE0152T Installation Guide

Power Specifications

The power specifications for the NE0152T are listed in the following table.

Table 15.

NE0152T AC power specifications

Specification

Measurement

Number of power supplies

2 (1+1 load sharing/redundant)

AC-input frequency (universal)

50–60 Hz

AC-input voltage (universal)

100–240 VAC

AC inrush current

18.6 A

AC-input current (typical)

0.591 A (120 V @ 60 Hz)

AC-input current (maximum)

0.637 A (120 V @ 60 Hz)

Power supply rated output power

156 W

System power dissipation (typical)

70.9 W (120 V @ 60 Hz)

System power dissipation (maximum)

76.4 W (120 V @ 60 Hz)

DC-output current (typical)

6.6 A @ 12 V

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands