Lenovo ThinkSystem NE0152T Installation Manual Download Page 20

Page: 20 / 110

NE0152T Installation Guide

Switch Unit

The NE0152T is a 1U rack-mountable GbE switch. You can mount the switch in
either the horizontal or vertical orientation.

The following illustrations show the features on the front and rear of the switch.

Figure 1.

ThinkSystem NE0152T front panel

Figure 2.

ThinkSystem NE0152T management panel detail

Figure 3.

ThinkSystem NE0152T rear panel

10/100/1000 BASE-T RJ45 Ports

10 GbE SFP+ Ports

Management Panel

Micro-USB Serial Console Port

USB Port

Reset Button

RJ45

Management Port

Status LEDs

Fan Modules

Power Supply Modules

IEC 320

Power Connector

IEC 320

Power Connector

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands