Lenovo ThinkSystem NE0152T Installation Manual Download Page 107

Page: 107 / 110

Appendix C: Technical Specifications

107

Environmental Specifications

The environmental specifications for the NE0152T are listed in the following table.

Table 14.

NE0152T environmental specifications

Specification

Measurement

Temperature, ambient operating

0 °C to +40 °C (32 °F to 104 °F)

Temperature (one fan failure),
operating

0 °C to +40 °C (32 °F to 104 °F)

Temperature, storage

-40 °C to +75 °C (-40 °F to 167 °F)

Relative humidity (non-condensing),
operating

10 to 90%

Relative humidity (non-condensing),
storage

5 to 95%

Altitude, operating

-60 m to +2000 m (-196.85 to +6561.7 ft)

Altitude, storage

N/A

Acoustic noise

Less than 65 dB

Heat dissipation

242 BTU/hr (typical)
261 BTU/hr (maximum)

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands