Lenovo ThinkSystem NE0152T Installation Manual Download Page 63 | Manualshive

Page: 63 / 110

background image

© Copyright Lenovo 2018

Chapter 4: Removing and Replacing Components

63

Removing the NE0152T from a Standard Equipment Rack

This section describes how to remove the NE0152T from a standard 19-inch
equipment rack. For information about removing the switch from other supported
racks, see the appropriate section in this chapter.

To remove the NE0152T from a standard rack, complete the following steps:

1.

Disconnect all external cables.

2.

If the air-duct option has been installed, remove it as described in

“Removing the

Air-Duct Option” on page 69

.

3.

Loosen and remove M6 screws (Item 3) and clip nuts (or cage nuts - Item 4) to
release the switch unit from the rack. Slide the switch unit out of the rack.

4.

Loosen and remove the M4 screws attaching the mounting bracket on each side of
the switch.

5.

If replacing the unit with another NE0152T, see

“Replacing the NE0152T” on page 70

.

3

4

2

1

«
...
61
62
63
64
65
...
»

Summary of Contents for ThinkSystem NE0152T















































































































Reviews:

No comments

Related manuals for ThinkSystem NE0152T

dominion kx III

Brand: Raritan Pages: 6

Brand: Raritan Pages: 5

DOMINION KSX II

Brand: Raritan Pages: 7

Brand: Raritan Pages: 2

Brand: Adler Pages: 8

PowerSwitch Z9332F-ON

Brand: Dell EMC Pages: 16

Brand: Indu-Sol Pages: 9

EdgePoint EP-S16

Brand: Ubiquiti Pages: 22

Brand: H3C Pages: 57

UHB-U3P1U2P3P-01

Brand: Gembird Pages: 2

RMQ-Titan M22-LED Series

Brand: Eaton Pages: 4

Brand: Microsens Pages: 8

Brand: KYLAND Pages: 34

Brand: TRENDnet Pages: 2

velatia cgm.3 system

Brand: Ormazabal Pages: 76

Brand: Xantech Pages: 12

Brand: IPGARD Pages: 15

Brand: Lindy Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands