Lenovo ThinkSystem NE0152T Installation Manual Download Page 38

Page: 38 / 110

NE0152T Installation Guide

Statement 26

CAUTION:

Do not place any object on top of rack-mounted devices.

To install the NE0152T in a standard equipment rack, complete the following steps:

Locate, record, and retain the product switch information in order to configure and
register your product. See

“Before Installing the NE0152T” on page 32

Note:

If this switch is a replacement switch, copy the product information from the

original switch onto the RID label that is shipped with replacement switch and
affix the new label to the bottom of the new switch.

Attach a mounting bracket (Item 1) to each side of the switch with M4 screws
(Item 2). Torque the screws to approximately 2.0 newton-meters (Nm) ± 0.1 Nm
(17.7 inch-pounds).

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands