Lenovo ThinkSystem NE0152T Installation Manual Download Page 109

Page: 109 / 110

Appendix C: Technical Specifications

109

Switching Performance

The feature performance characteristics of the NE0152T are listed in the following
table.

Note:

The specific features supported on your switch, as well as some capacity and

performance characteristics, depend on the specific firmware installed. For more
information, see the

Application Guide

and

Command Reference

for your specific

switch and its installed firmware.

Table 16.

NE0152T feature performance characteristics

Feature

Characteristics

Switching architecture

Non-blocking

Throughput

88 Gbps full-duplex

Ethernet line rate

100%

IEEE 802.1Q VLANs

4096, with 4K VLAN IDs
up to 4092 VLANs can be configured

Forwarding database entries

65K

Configurable physical interfaces

53 (static or DHCP):
52 data ports + 1 management port

ARP entries

15872

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands