Lenovo ThinkSystem NE0152T Installation Manual Download Page 82 | Manualshive

Page: 82 / 110

background image

82

NE0152T Installation Guide

The GRUB Menu

The Lenovo ThinkSystem NE0152T RackSwitch does not use a Boot Management
menu. Instead, all images are preloaded, and all booting options, such as switching
boot images, are included in the GNU GRUB bootloader. To boot CNOS or switch
images on the NE0152T:

1.

Boot the switch. Eventually the GNU GRUB bootloader displays. Select the image
you want to use (either

CNOS slot 1

or

CNOS slot 2

).

2.

The system automatically loads CNOS and prompt you to log in.

Welcome to GRUB!

GNU GRUB version 2.00

+----------------------------------------------------------------------+
|CNOS slot 1         |
|CNOS slot 2         |
|Recovery Mode         |
|ONIE            |
|            |
|            |
|            |
|            |
|            |
+----------------------------------------------------------------------+

Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, `e' to edit the commands
before booting or `c' for a command-line. ESC to return
previous menu.

«
...
80
81
82
83
84
...
»

Summary of Contents for ThinkSystem NE0152T















































































































Reviews:

No comments

Related manuals for ThinkSystem NE0152T

Brand: StarTech.com Pages: 2

MIEN2208 Series

Brand: Maiwe Pages: 5

Brand: JAR Systems Pages: 2

Brand: Surefire Pages: 2

Brand: Woxcon Pages: 42

Brand: TAXON TOOLS Pages: 9

MISCOM7220G-4GF-16GT

Brand: Maiwe Pages: 6

Brand: CAMBRIONIX Pages: 37

Brand: Maipu Pages: 135

Brand: Minicom Pages: 16

Brand: Pilz Pages: 20

Brand: Omega Pages: 17

IES2016-16T Series

Brand: 3onedata Pages: 3

Brand: AMBIENTECH Pages: 4

Brand: Foxun Pages: 7

Brand: Holley Pages: 2

DH-PFS4428-24GT-370

Brand: Dahua Technology Pages: 44

Brand: SMART-AVI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands