Lenovo ThinkSystem NE0152T Installation Manual Download Page 64

Page: 64 / 110

NE0152T Installation Guide

Removing the NE0152T from a Lenovo System x or Power
Rack

This section describes how to remove the NE0152T from a Lenovo System x or
Power 4-post rack.

To remove the NE0152T from a System x or Power rack, complete the following steps:

Disconnect all external cables.

If the air-duct option has been installed, remove it as described in

“Removing the

Air-Duct Option” on page 69

Loosen and remove M3.5 screws that secure the rear brackets to the front brackets.

Loosen and remove the M6 screws and clip nuts (or cage nuts) that attach the filler
plate and rear mounting brackets to the rear rack posts.

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands