Lenovo ThinkSystem NE0152T Installation Manual Download Page 69

Page: 69 / 110

Chapter 4: Removing and Replacing Components

Removing the Air-Duct Option

The NE0152T supports an optional 1U air duct to maximize air flow conditions in a
Lenovo Power Systems Group rack.

To remove an installed 1U air-duct option from a 19” rack, complete the following
steps.

Loosen the M4 thumbscrews securing the air-duct unit to the mounting brackets.

Slide the 1U air-duct unit out of the rack.

To return the component to customer service for replacement, see

Appendix A,

“Getting Help and Technical Assistance“

to help you gather all the required

information. After you remove the component, securely pack it for shipping.

For instructions to install a replacement air-duct option, see

“Installing the Air-Duct

Option” on page 47

thumbscrews

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands