Lenovo ThinkSystem NE0152T Installation Manual Download Page 31

Page: 31 / 110

Chapter 3. Installing NE0152T Hardware and Options

This chapter describes how to install the NE0152T hardware and options. The
following topics are covered:



“Before Installing the NE0152T” on page 32



How to record important product information



Tools required for installation



A list of items included in the package



Environmental requirements



Vital safety information



Installing the switch in one of the supported rack types



“Installing the NE0152T in a Standard Equipment Rack” on page 37



“Installing the NE0152T in a Lenovo System x or Power Rack” on page 40



“Installing the NE0152T in a Lenovo iDataPlex Rack” on page 44



“Installing the Air-Duct Option” on page 47



“Installing Port Transceivers” on page 51

Note:

For information on removing or replacing installed NE0152T components,

see

Chapter 4, “Removing and Replacing Components“

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands