manualshive.com logo in svg

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 163 / 246

Share
Download
Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 163

b.  Position the new memory module over the memory slot. Ensure that the notch 

1 

on the memory 

module aligns correctly with the slot key 

2 

on the system board. Push the memory module straight 

down into the slot until the retaining clips close.  

Note:

Do not touch the circuit board of the memory module.

Figure 105. Installing the memory module

c.  Reinstall the direct cooling air baffle. See “Direct cooling air baffle” on page 107.

What to do next: 

•  To work with another piece of hardware, go to the appropriate section.

•  To complete the installation or replacement, go to “Completing the parts replacement” on page 210.

PCIe card

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter 

1 “Read this first: Important safety information” on page 1. 

Your computer has the following PCIe card slots: 

•  PCIe 3.0 x4 card slots

•  PCIe 3.0 x16 card slots

Notes: 

•  PCIe cards available vary by computer model.

•  To remove or install a full-length PCIe card, see “Full-length PCIe card” on page 163.

•  If you want to use an NVIDIA compute card, ensure that your computer also has an NVIDIA graphics card 

installed.

PCIe card installation rules

Install PCIe cards in the alphabetic order as shown. 

Chapter 9

.

Hardware removal and installation

155

Summary of Contents for ThinkStation P920























































































































































































































































Reviews:

No comments