Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 115

Page: 115 / 246

8. Route the cable of the new cover presence switch, and align the notch

on the cover presence switch

with the tab

in the chassis. Then pivot the cover presence switch bracket as shown until it snaps into

position.

Figure 15. Installing the cover presence switch bracket

9. Connect the cable of the new cover presence switch to the system board. See “Parts on the system

board” on page 38.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 210.

Direct cooling air baffle

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To remove or install the direct cooling air baffle, do the following:

1. Prepare your computer. See “Preparing your computer and removing the computer cover” on page 103.

Chapter 9

Hardware removal and installation

107

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 115 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: