Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 153

Page: 153 / 246

c. Press the mounting stud downward and press the mounting stud downward. Then, turn the

mounting stud 90-degree clockwise to secure the heat sink to the M.2 solid-state drive holder.

Figure 86. Securing the heat sink to the M.2 solid-state drive holder

9. To install the M.2 solid-state drive holder, do the following:

a. Align the notch

on the M.2 solid-state drive with the slot key

in the M.2 solid-state drive slot.

Then, slide the holder against the multi-function bracket and press the holder downward until the M.2
solid-state drive is securely seated.

Note:

Do not touch the circuit board of the M.2 solid-state drive.

Figure 87. Installing the M.2 solid-state drive holder

Chapter 9

Hardware removal and installation

145

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 153 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: