Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 84

Page: 84 / 246

3. Under

RAID Volumes

, select the RAID volume that you want to delete and press Enter. The RAID

VOLUME INFO window is displayed.

4. Select

Delete

under

Volume Actions

and press Enter. When prompted, select

Yes

and press Enter to

confirm the deletion of the selected RAID volume.

5. To save settings and exit the Setup Utility program, press F10 or Fn+F10 (depending on the keyboard

settings), select

Yes

in the window displayed, and press Enter.

Configuring RAID with AVAGO MegaRAID Configuration Utility

To configure RAID with AVAGO MegaRAID Configuration Utility, ensure that:

• An AVAGO MegaRAID adapter is installed in your computer.

• The storage drives used for RAID configuration are connected to the installed AVAGO MegaRAID adapter

instead of the system board.

Storage drive requirements for RAID levels

Your computer supports the following RAID levels:

• RAID 0: striped disk array

– Consists of at least two SATA or Serial Attached SCSI (SAS) storage drives

– Supported strip size: 64 KB, 128 KB, 256 KB, 512 KB, or 1 MB

– Better performance without fault tolerance

• RAID 00: spanned storage drive group with a series of RAID 0 storage drive groups

– Consists of two or four SATA or SAS storage drives

– Supported strip size: 64 KB, 128 KB, 256 KB, 512 KB, or 1 MB

– Better performance without fault tolerance

• RAID 1: mirrored disk array

– Consists of two or four SATA or SAS storage drives

– Improved read performance and 100% redundancy

• RAID 10: striped and mirrored disk array (a combination of RAID 0 and RAID 1)

– Consists of four SATA or SAS storage drives

– Data being striped across storage drive groups

– Provides both high data transfer rates and complete data redundancy

• RAID 5: block-level striped disk array with distributed parity

– Consists of at least three SATA or SAS storage drives

– Supported strip size: 64 KB, 128 KB, 256 KB, 512 KB, or 1 MB

– Better performance and fault tolerance

– Available only on some models of AVAGO MegaRAID adapters

• RAID 6: block-level striped disk array with dual distributed parity

– Consists of at least four SATA or SAS storage drives

– Supported strip size: 64 KB, 128 KB, 256 KB, 512 KB, or 1 MB

– Better performance and fault tolerance that can stand up to loss of two storage drives

– Available only on some models of AVAGO MegaRAID adapters

P920 Hardware Maintenance Manual

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 84 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: