Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 124

Page: 124 / 246

a. Note the orientation of the connector on the new storage drive. Then, flex both sides of the adapter

and align the four pins

with the corresponding holes in the storage drive.

Note:

Do not touch the circuit board (if accessible) of the 2.5-inch storage drive.

Figure 31. Installing the storage drive into the adapter

b. Align the four tabs on the adapter with the corresponding notches

in the converter. Then, slide the

storage drive as shown until the tab

snaps into position. The adapter with the storage drive is

installed into the converter.

Figure 32. Installing the adapter into the converter

116

P920 Hardware Maintenance Manual

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 124 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: