manualshive.com logo in svg

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 210 / 246

Share
Download
Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 210

e.  Turn the heat-sink-and-fan assembly upside down. Release two retaining clips 

1 

at the corner of the 

microprocessor retainer and then release the other two retaining clips 

2 

as shown. Then, lift the 

retainer 

3 

with the microprocessor from the heat-sink-and-fan assembly. 

Figure 180. Removing the microprocessor retainer from the heat-sink-and-fan assembly

Note:

Set aside the microprocessor retainer with the microprocessor. Ensure that the thermal 

grease on the bottom of the microprocessor does not get in contact with anything.

5.  To install a heat-sink-and-fan assembly on the system board, do the following: 

a.  If necessary, apply appropriate amount of thermal grease to the bottom of the heat-sink-and-fan 

assembly as shown.  

Figure 181. Applying thermal grease on the heat-sink-and-fan assembly

202

P920 Hardware Maintenance Manual

Summary of Contents for ThinkStation P920























































































































































































































































Reviews:

No comments