Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 109

Page: 109 / 246

Message/Symptom

FRU/Action

Program loads from the hard disk with a known-good
diagnostics diskette in the first 3.5-inch diskette drive

1. Run the Setup Utility program and check the Startup

sequence.

2. Diskette Drive

3. Diskette Drive Cable

4. System Board

5. Power Supply

RPL computer cannot access programs from its own hard
disk.

1. If the network administrator is using LCCM Hybrid

RPL, check the startup sequence:

First device - network

Second device - hard disk

2. Hard disk drive

RPL computer does not RPL from server

1. Check the startup sequence.

2. Check the network adapter LED status.

Serial or parallel connector device failure (system board
connector)

1. External Device Self-Test OK?

2. External Device

3. Cable

4. System Board

Serial or parallel connector device failure (adapter
connector)

1. External Device Self-Test OK?

2. External Device

3. Cable

4. Alternate Adapter

5. System Board

Some or all keys on the keyboard do not work

1. Keyboard

2. Keyboard Cable

3. System Board

Undetermined problems

This section provides instructions on how to find out the failing devices or adapters.

1. Turn off the computer.

2. Remove or disconnect the following components (if installed) one at a time.

a. External devices (modem, printer, or mouse)

b. Any adapters

c. Memory modules

d. Extended video memory

e. External Cache

f. External Cache RAM

g. Hard disk drive

h. Diskette drive

3. Turn on the computer to retest the system.

Chapter 8

Service checkout and symptom-to-FRU index

101

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 109 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: