Lenovo ThinkStation P920 Hardware Maintenance Manual Download Page 190

Page: 190 / 246

a. Insert the Wi-Fi card into the mini PCIe slot on the Wi-Fi adapter. Install two screws to secure the Wi-

Fi card to the Wi-Fi adapter. Connect two Wi-Fi antenna cables to the Wi-Fi card.

Figure 141. Installing the Wi-Fi card

b. Install the Wi-Fi adapter into the PCIe card slot on the system board. See “Parts on the system

board” on page 38.

Figure 142. Installing the Wi-Fi adapter

c. Pivot the PCIe card latch and push it back in until it snaps into position.

d. If the installed Wi-Fi card supports the Bluetooth function, connect a Bluetooth cable to the Wi-Fi

adapter.

Note:

The Bluetooth cable connects the Bluetooth connector on the Wi-Fi adapter to the 15-in-1

card reader connector on the system board. See “Parts on the system board” on page 38.

182

P920 Hardware Maintenance Manual

Summary of Contents for ThinkStation P920























































































































































































































































Search results

Summary of Contents for ThinkStation P920

Reviews:

Lenovo ThinkStation P920, Hardware Maintenance Manual, Page: 190 / 246

Search results

Summary of Contents for ThinkStation P920

Reviews: