Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual Download Page 183

Page: 183 / 186

particulate contamination 158
parts replacement, completing 142
password

considerations 46
setting, changing, deleting 47
Setup Utility program 46

power supply status LEDs

configuring 50
introduction 50

RAID 110i key

installing 74
removing 74

RAID 500 or 520i upgrade key

installing 76
removing 77

RAID card

locations 26

rear view of the server

reliability, availability, and serviceability

features 9

removing

cooling shroud     60
DIMM    68
intrusion switch     93

–94

memory module    68
optical module 91
RAID 110i key     74
RAID 500 or 520i upgrade key  77
SD module     81
server cover     57
ThinkServer RAID Super Capacitor Module 82, 84
ThinkServer Trusted Platform Module    72
TMM    79
TSM Premium module  70

easy-swap-drive module 126
front panel board 129

front VGA and USB module  131
hardware    55
hot-swap hard disk drive      109
hot-swap hard-disk-drive backplane  124
hot-swap redundant power supply 108
microprocessor     101
riser card assembly  133
system board     137
system fan  128

Setup Utility program 45

installing 142
removing 57

server documentation 2
server package 7
server setup

road map 5

service, getting 151 s etting,
changing, deleting

password 47

Setup Utility program

Ethernet connector     48
exiting    48
interface     43
password    46
starting     43
TPM     48
using     43

slim optical drive

locations 17, 19

software 12

Lenovo ThinkServer Deployment Manager 13

specifications 11
starting

Setup Utility program 43

startup device

selecting 47
Setup Utility program 47

static-sensitive devices

guidelines 56

static-sensitive devices, handling 56
system board 33

replacing 137

169

Summary of Contents for ThinkServer RD350G



























































































































































































Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands

Lenovo ThinkServer RD350G, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands