Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual Download Page 44

Page: 44 / 186

ThinkServer RAID 720i PCIe Adapter

The RAID 720i Adapter provides advanced SATA/SAS hardware RAID functions. The following illustration
shows the connectors on the adapter.

Figure 12. ThinkServer RAID 720i PCIe Adapter

Connector 0

Used to connect the mini-SAS signal cable connector on the backplane to support HDD 0-3.

Connector 1

Used to connect the mini-SAS signal cable connector on the backplane to support HDD 4-7.

Thunderbolt Flash Module connector

Used to connect a Thunderbolt Memory module (hereinafter referred to as TMM).

Hot-swap-drive backplane

Your server comes with one of the following drive bay and backplane configurations:

Drive bay size

Drive bay quantity

Backplane quantity

Drive type

3.5-inch

Hot-swap, SATA or SAS

Hard disk drive or 2.5-inch
solid-state drive

2.5-inch

Hot-swap, SATA or SAS

Hard disk drive or solid-state
drive

To locate the backplanes, see

“Server components” on page 23.

ThinkServer RD350G User Guide and Hardware Maintenance Manual

Summary of Contents for ThinkServer RD350G



























































































































































































Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands

Lenovo ThinkServer RD350G, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands