Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual Download Page 137

Page: 137 / 186

Figure 97. Installing the optical drive

8. Connect the connector

to the rear of the optical drive.

Figure 98. Connecting the connector

to the rear of the optical drive

9. If necessary, connect the other end of the signal cable to the SATA connector for the optical drive on

the system board. See

“System board components” on page 33.

10. If you are instructed to return the old optical drive, follow all packaging instructions and use any

packaging materials that are supplied to you for shipping.

What to do next:

• To work with another piece of hardware, go to the appropriate section.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 142.

Chapter 6

Replacing hardware

123

Summary of Contents for ThinkServer RD350G



























































































































































































Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands

Lenovo ThinkServer RD350G, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands