Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual Download Page 47

Page: 47 / 186

System board components

The following illustration shows the component locations on the system board.

Figure 17. System board components

SATA connector (optical drive)

Coin-cell battery

SATA connector 1 (ports 4

–7)

Storage-drive power connector

SATA connector 0 (ports 0

–3)

Front panel connector 1

Front panel connector 2

SD module connector

Riser card assembly 1 slot

TSM Premium module connector

TPM connector

PCIe slot

Riser card assembly 2 slot

RAID upgrade key connector

Power supply connector 2

Power supply connector 1

Intrusion switch connector

Backplane power connector 2

Backplane power connector 1

System fan 6 connector

Microprocessor 2 memory slots (4)

System fan 5 connector

Microprocessor 2 socket

System fan 4 connector

Microprocessor 2 memory slots (4)

Microprocessor 1 memory slots (4)

System fan 3 connector

System fan 2 connector

Microprocessor 1 socket

System fan 1 connector

Microprocessor 1 memory slots (4)

Chapter 3

Product overview

Summary of Contents for ThinkServer RD350G



























































































































































































Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands

Lenovo ThinkServer RD350G, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands