Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual Download Page 33

Page: 33 / 186

Front panel

The following illustration shows the controls, connectors, and LEDs on the front panel of the server. The
front panel varies by model.

Figure 5. Front panel

Network status LED

System health LED

Power button with power status LED

System ID button with ID LED

USB 2.0 connectors (2)

VGA connector

Network status LED

The network status LED on the front panel helps you identify the network connectivity and activity.

Network status LED

Color

Description

Green

The server is connected to a LAN.

Off

None

The server is disconnected from a LAN.

Blinking

Green

The LAN is connected and active.

Chapter 3

Product overview

Summary of Contents for ThinkServer RD350G



























































































































































































Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands

Lenovo ThinkServer RD350G, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands