Lenovo ThinkServer RD350G User Manual And Hardware Maintenance Manual Download Page 40

Page: 40 / 186

FRU description

Self-service CRU

Optional-service CRU

Coin-cell battery

Yes

Cooling shroud

Yes

Easy-swap-drive module*

Yes

Easy-swap storage drive*

Yes

Front panel board

Yes

Front VGA and USB module

Yes

Heat sink

Yes

Hot-swap-drive backplane

Yes

Hot-swap redundant power supply

Yes

Hot-swap storage drive*

Yes

Intrusion switch*

Yes

Lenovo ThinkServer RAID 110i upgrade key*

Yes

Lenovo ThinkServer RAID 500 upgrade key*

Yes

Lenovo ThinkServer RAID 520i upgrade key*

Yes

Lenovo ThinkServer RAID 720i Modular DRAM
Upgrade*

Yes

Lenovo ThinkServer RAID 720i Modular Flash*

Yes

Lenovo ThinkServer RAID Super Capacitor Module*

Yes

Lenovo ThinkServer RAID Super Capacitor Module
holder*

Yes

Lenovo ThinkServer System Manager Premium
module*

Yes

Lenovo ThinkServer Trusted Platform Module*

Yes

Memory module

Yes

Microprocessor

Yes

Optical drive*

Yes

Optical module*

Yes

PCIe card*

Yes

Power cord*

Yes

Rack handles

Yes

Riser card

Yes

SD card*

Yes

SD module*

Yes

System board

System fan

Yes

RAID card

This topic provides information to help you locate the connectors on a RAID card. If your server has a RAID
card installed, the RAID card is seated on the riser card assembly 2.

ThinkServer RD350G User Guide and Hardware Maintenance Manual

Summary of Contents for ThinkServer RD350G



























































































































































































Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands

Lenovo ThinkServer RD350G, User Manual And Hardware Maintenance Manual

Search results

Summary of Contents for ThinkServer RD350G

Reviews:

Related manuals for ThinkServer RD350G

Brands by name

Popular brands