Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 34

Page: 34 / 84

Step 5. Extend the rail until the front mounting bracket of the rail reaches the front rack.

Step 6. Repeat steps Step 1

on page 25 through Step 3

on page 25 to install the front rail mounting

bracket to the front mounting flange.

Note:

Do not secure the front mounting bracket of the rail with screws until you install the storage

enclosure into the rack.

Step 7. Repeat steps Step 1

on page 25 through Step 6

on page 26 to install the opposite rail in the

rack.

The installation of the storage block slide rails in a round hole rack is now complete.

To continue with the installation of the ThinkAgile CP storage block, follow these steps: “Install the storage
enclosure” on page 29

Lenovo ThinkAgile CP Hardware Installation Guide

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands