Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 37 | Manualshive

Page: 37 / 84

background image

Install the storage enclosure

Procedures for installing ThinkAgile CP storage enclosure in a rack.

To install the ThinkAgile CP storage enclosure on the slide rails, do the following:

CAUTION:
Ensure that at least two people lift and install the enclosure together.

Step 1. Remove both of the side covers on the enclosure by grasping and pulling out the bottom of each

side cover, and then pulling it straight up.

Figure 12. Removal of side cover

Step 2. Lift the enclosure and slowly place the enclosure on the rail.

.

ThinkAgile CP Setup

29

«
...
35
36
37
38
39
...
»

Summary of Contents for ThinkAgile CP 4000 Series





















































































Reviews:

No comments

Related manuals for ThinkAgile CP 4000 Series

Brand: QNAP Pages: 20

Compact Emulator M30620T-CPE

Brand: Renesas Pages: 52

Brand: Taiwan Commate Computer Inc. Pages: 29

MasterBus Tanklevel Interface

Brand: Mastervolt Pages: 8

PARTNER PC CARD

Brand: Avaya Pages: 4

Brand: ZyXEL Communications Pages: 244

Brand: Aethra Pages: 2

Brand: SeaLevel Pages: 21

RP614 - Web Safe Router

Brand: NETGEAR Pages: 16

Accelero TWIN TURBO II

Brand: Arctic Pages: 2

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

Brand: Alcatel-Lucent Pages: 60

Brand: TP-Link Pages: 16

Brand: Watchguard Pages: 21

Brand: Dantel Pages: 22

Brand: Ruckus Wireless Pages: 4

Brand: bintec elmeg Pages: 32

Brand: Kontron Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands