Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 28

Page: 28 / 84

ThinkAgile CP Package Contents

This section includes the package contents for the ThinkAgile CP solution.

The ThinkAgile CP solution is delivered in several boxes:

• Storage block box

• Compute block box

• Interconnect switch box

• Ship group box

• Management switch box (optional)

Attention:

• The number of boxes depends on the number of storage and compute blocks included in your ThinkAgile

CP configuration.

• Check the contents of each box before installing the ThinkAgile CP solution. If any of the box items are

missing or are damaged, contact your place of purchase.

Storage block box

The storage block box contains the following items:

• One storage block

• One storage slide rails box:

– One left slide rail

– One right slide rail

– Six M5 screws

– Eight screws for square hole rack

• Two Category 5e patch cables

• Eight Category 6 patch cables

• Eight SFP+ 10 GbE transceivers

Compute block box

The compute block box contains the following items:

• One compute block

• One compute slide rails box:

– One left slide rail

– One right slide rail

– Two M5 screws

– Two washers

• One Category 5e patch cable

• Two power cords

• Two SFP+ 10 GbE Direct Attach Cables (DACs)

Lenovo ThinkAgile CP Hardware Installation Guide

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands