Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 77

Page: 77 / 84

• Connect the top-of-rack switches to the customer network.

• Perform basic network configuration to integrate the ThinkAgile CP rack into the customer environment.

• Ensure that the product adheres to the ThinkAgile CP Best Recipe firmware profile.

• Configure the ThinkAgile CP user interface (e.g., SMTP, Pulse, containers) and license.

• Verify the product environment, to ensure a successful handover.

• Provide a knowledge transfer to the customer. This includes basic operational tasks and the support plan.

Lenovo Professional Services will provide information about the configured system, for your records.

The following items are not in the scope of the initial ThinkAgile CP engagement. Many of these can be
handled via other available Professional Services offerings.

• Hardware installation services

• Server applications installation or configuration

• Advanced hypervisor configuration

• Complete administrative or operations training

• Data migration from existing storage systems and hypervisor environments

• Installation assistance for nonstandard hardware components or components not purchased from

Lenovo. Be aware that this activity can affect support for the product.

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands