Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 43

Page: 43 / 84

Install the compute enclosure

Procedures for installing ThinkAgile CP compute enclosure in a rack.

CAUTION:
Ensure that at least two people lift and install the enclosure together.

Figure 21. Front latches on slide rails

To install the ThinkAgile CP compute enclosure on the slide rails, do the following:

Step 1. Pull the slide rails forward until the rails click into place.

Step 2. Push up the front latches.

Step 3. Pull the slide rails all the way out.

Attention:

You can only install the compute block enclosure successfully when the slide rails are

fully extended.

Step 4. Remove all compute nodes and the shuttle from the enclosure.

Step 5. Carefully lift the enclosure.

Step 6. Tilt and lower the enclosure; then, push the slide rails toward the enclosure and make sure the

farthest nailheads on each side go into the slots on the slide rails.

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands