Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 40

Page: 40 / 84

Install the ThinkAgile CP compute block

Procedures for installing ThinkAgile CP compute block in a rack.

To install the ThinkAgile CP compute block in a rack, do the following:

1. Unpack the compute block box and check the contents

2. Install the slide rails into the rack

3. Install the enclosure on the slide rails

4. Slide the compute enclosure into the rack

Firstly, unpack the storage block box and check the contents:

• One compute block

• One compute slide rails box:

– One left slide rail

– One right slide rail

– Two M5 screws

– Two washers

• One Category 5e patch cable

• Two power cords

• Two SFP+ 10 GbE Direct Attach Cables (DACs)

Note:

If any of the slide box items are missing or are damaged, contact your place of purchase.

Figure 16. ThinkAgile CP compute slide rails box contents

Lenovo ThinkAgile CP Hardware Installation Guide

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands