Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 35

Page: 35 / 84

Install the storage slide rails into a square hole rack

Procedures for installing ThinkAgile CP storage block slide rails in a square hole rack.

To install the ThinkAgile CP storage block slide rails in a square hole rack, do the following:

Attention:

Ensure that you install the rear mounting rail brackets before installing the front mounting

brackets.

Figure 11. Installing the rail in a square hole rack

Step 1. Open the hinge bracket on the rear of the rail.

Step 2. Remove the preinstalled screw pins for round hole rack.

Step 3. Line up the holes on the rear of the rail with the corresponding holes in the rear-mounting flange of

the rack.

Step 4. Close the hinge bracket to secure the rail to the rack flange.

Step 5. Secure the rear mounting bracket of the rail with two screws for square hole rack.

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands