Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 31

Page: 31 / 84

Install the ThinkAgile CP storage block

Procedures for installing ThinkAgile CP storage block in a rack.

To install the ThinkAgile CP storage block in a rack, you must do the following:

1. Unpack the storage block box and check the contents

2. Install the slide rails in the rack

3. Install the storage enclosure

Firstly, unpack the storage block box and check the contents:

• One storage block

• One storage slide rails box:

– One left slide rail

– One right slide rail

– Six M5 screws

– Eight screws for square hole rack

• Two Category 5e patch cables

• Eight Category 6 patch cables

• Eight SFP+ 10 GbE transceivers

Note:

If any of the slide box items are missing or are damaged, contact your place of purchase.

Figure 8. ThinkAgile CP storage slide box contents

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands