Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 49

Page: 49 / 84

Step 6. Verify basic switch operation by checking the system LEDs. When operating normally, the PSU1/

PSU2, Diag, and Fan LEDs should all be green.

Step 7. Connect the network cables.

a. For the RJ-45 Management port, connect 100-ohm Category 5, 5e or better twisted-pair cable.

b. Connect DAC cables to the SFP+/QSFP+ slots. Or first install SFP+/QSFP+ transceivers and

then connect fiber optic cabling to the transceiver ports.

The following transceivers are supported:

• 40G QSFP+ SR4 Transceiver 90Y3505

• 10G BASE-T (RJ45) SFP Transceiver SBB7A02090

• 10G SFP+ SR Transceiver 46C3446

Note:

As connections are made, check the port status LEDs to be sure the links are valid.

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands