Lenovo ThinkAgile CP 4000 Series Hardware Installation Manual Download Page 55

Page: 55 / 84

Cabling a single-interconnect configuration

Procedures for cabling theThinkAgile CP single-interconnect switch configuration.

Complete these procedures to cable a single-interconnect configuration.

Hardware management network connections

Connect the following ports to the management switch:

• Interconnect port 47 using a SFP+ Direct Attach Cable (DAC)

• Compute block port (C.M.) using a RJ45 patch cable

• Upper storage block port (S.U.M.) using a RJ45 patch cable

• Lower storage block port (S.L.M.) using a RJ45 patch cable

Figure 28. Hardware management network connectivity in a single interconnect configuration

Note:

If not using the Lenovo ThinkSystem NE0152T RackSwitch as the management switch, you may

require different cables for the management network connections.

Chapter 3

ThinkAgile CP Setup

Summary of Contents for ThinkAgile CP 4000 Series





















































































Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands

Lenovo ThinkAgile CP 4000 Series, Hardware Installation Manual

Search results

Summary of Contents for ThinkAgile CP 4000 Series

Reviews:

Related manuals for ThinkAgile CP 4000 Series

Brands by name

Popular brands