manualshive.com logo in svg

Lantronix PremierWave 2050, Command Reference Manual, Page: 82 / 428

Share
Download
Lantronix PremierWave 2050 Command Reference Manual Download Page 82

5:  Commands and Levels 

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference 

82 

gap timer 

<milliseconds>

 

Sets the gap timer in milliseconds. If some data has been 
received, it will be forwarded after this time since the last 
character. 

interface bluetooth-rfcomm 

Sets the line interface to bluetooth-rfcomm. 

kill session 

Kills command mode session on the Line 

line 

<line>

 

Enters the line level. <line> = number of the line (serial 
port) to be configured. 

line mode serial device 

Sets the line to serial device mode. 

name 

<text>

 

Sets the name for this line. 

no clear line counters 

Restores the serial counters to the aggregate values. 

no command mode 

Disables command mode for the current line. 

no command mode signon message 

Clears the signon message displayed at boot time and 
when entering command mode. 

no gap timer 

Removes the gap timer, so forwarding depends on the 
line speed. 

no name 

Removes the name of this line. 

protocol none 

Uses no protocol on the line. 

protocol tunnel 

Applies tunnel protocol on the line. 

show 

Displays the current status. 

show bluetooth line 

Displays the current configuration. 

show command mode 

Shows the command mode settings for the current line. 

show history 

Displays the last 20 commands entered during the current 
CLI session. 

show statistics 

Shows the line statistics. 

state disable 

Disables the line so data cannot be sent/received. 

state enable 

Enables the line so data can be sent/received. 

terminal 

<line>

 

Enters the configure-terminal level. <line> = number of the 
terminal line (serial port) to be configured. 

terminal network 

Enters the configure-terminal level for the network. 

threshold 

<bytes> 

 

Sets the threshold in bytes. After this many bytes are re-
ceived, they are forwarded without delay. 

tunnel 

<line>

 

Enters the tunnel level. <line> = number of the tunnel line 
(serial port) to be configured. 

usb 

<line>

 

Enters the usb level. <line> = number of the line (usb port) 
to be configured. 

write 

Stores the current configuration in permanent memory. 

bridge 1 (config-bridge:br0) level commands 

auto detect ip address disable 

Disables learning the IPv4 address of the bridged client. 

auto detect ip address enable 

Enables learning the IPv4 address of the bridged client. 

bridging initial scan interval 

<seconds>

 

Sets the scan interval before learning the IP address of 
the bridged client. 

bridging ip address 

<IP address>

 

Sets the Bridging IP Address. 

bridging ipv6 address 

<ipv6 address>

 

Sets the Bridging IPv6 Address. IPv6 addresses are writ-
ten in eight groups of four hexadecimal digits separated 
by colons, such as 
2001:0db8:85a3:0000:0000:8a2e:0370:7334 Network 
address ranges are written in CIDR notation. A network is 
denoted by the first address in the block (ending in all 

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Reviews:

No comments