Lantronix PremierWave 2050 Command Reference Manual Download Page 8 | Manualshive

Page: 8 / 428

background image

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

8

1: About This Guide

This document describes how to configure the Lantronix® PremierWave® 2050 enterprise Wi-Fi®
IoT module using the Command Line Interface (CLI) and/or Extensible Markup Language (XML).
CLI provides an interactive mode for accessing the module configuration and management
interface. It is most suited for system and network administrators comfortable with using similar
interfaces on enterprise IT and networking products. It is also helpful as a quick tool for access via
the product's serial ports or console/management ports. XML provides an extensible mode for
software developers interfacing with the module and system integrators performing batch
provisioning/updates.

Chapter Summaries

This table lists and summarizes the content of each chapter.

Conventions

The table below lists and describes the conventions used in this book.

Chapter

Summary

2: Overview

Gives an overview of CLI and XML.

3: Command Line Interface

Lists commands and describes how to use CLI to configure the
PremierWave 2050 module.

4: Configuration Using XML

Lists XML Configuration Record (XCR) groups and items and describes
how to use XCRs to configure the PremierWave 2050 module.

5: Commands and Levels

Provides an index of the CLI command hierarchy with hyperlinks to the
corresponding command details.

Convention

Description

Bold text

Default parameters

Italic text

Required values for parameters.

Square Brackets [ ]

Optional parameters.

Angle Brackets < >

Possible values for parameters.

Pipe |

Choice of parameters.

Warning

Warning:

Means that you are in a situation that could cause equipment

damage or bodily injury. Before you work on any equipment, you must be
aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents.

Note

Note:

Means take notice. Notes contain helpful suggestions, information, or

references to material not covered in the publication.

Caution

Caution:

Means you might do something that could result in faulty

equipment operation or loss of data.

Screen Font

CLI terminal sessions and examples of CLI input are depicted in

courier new

font

.

«
...
6
7
8
9
10
...
»

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PremierWave 2050

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: Paradox Pages: 2

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

Brand: Intermatic Pages: 3

Brand: Victaulic Pages: 2

Brand: Carel Pages: 2

CIMR-VC*****H**-00 series

Brand: YASKAWA Pages: 32

ECL Comfort 300

Brand: Danfoss Pages: 75

Brand: sonitor Pages: 3

i-OLEG LumiGate GR-7610/V2

Brand: olympia electronics Pages: 2

Brand: TA Pages: 6

Brand: Grifco Pages: 20

Brand: S&S Northern Pages: 16

All Sport 1600 Series

Brand: Daktronics Pages: 92

Brand: Geeetech Pages: 48

Brand: Danfoss Pages: 16

Brand: Ibiza Pages: 37

Brand: WAFER Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands