Lantronix PremierWave 2050 Command Reference Manual Download Page 365

Page: 365 / 428

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

365

with secrets.

show wps status

Show status of WPS operation.

smartroam

Enter smartroam configuration level

start wps

Starts wi-fi protected setup operation.

start wps pin

Starts wi-fi protected setup operation.

status

Show link status

wifi direct go mode disable

Disables WiFi Direct Group Owner Mode.

wifi direct go mode enable

Enables WiFi Direct Group Owner Mode.

write

Stores the current configuration in permanent memory.

link (config-ethernet:eth0) level commands

clrscrn

Clears the screen.

credentials

<text>

Selects the RSA certificate by configured name.

default duplex

Restores the default duplex setting, which is auto.

default eap-ttls option

Restores the default EAP-TTLS protocol option, which is
EAP-MSCHAP V2.

default fast option

Restores the default FAST authentication protocol option,
which is MD5.

default fast provisioning

Restores the default FAST provisioning, which is Authen-
ticated

default ieee 802 1x

Restores the default IEEE 802.1x protocol, which is EAP-
TTLS.

default peap option

Restores the default PEAP authentication protocol option,
which is EAP-MSCHAP V2.

default speed

Restores the default speed setting, which is auto-
negotiate.

duplex auto

Sets duplex mode to auto.

duplex full

Sets duplex mode to full.

duplex half

Sets duplex mode to half.

eap-ttls option chap

Sets the EAP-TTLS authentication protocol option to
CHAP.

eap-ttls option eap-md5

Sets the EAP-TTLS authentication protocol option to EAP-
MD5.

eap-ttls option eap-mschapv2

Sets the EAP-TTLS authentication protocol option to EAP-
MSCHAP V2.

eap-ttls option mschap

Sets the EAP-TTLS authentication protocol option to
MSCHAP.

eap-ttls option mschapv2

Sets the EAP-TTLS authentication protocol option to
MSCHAP V2.

eap-ttls option pap

Sets the EAP-TTLS authentication protocol option to PAP.

eapol disable

Disables EAPoL Authentication.

eapol enable

Enables EAPoL Authentication

exit

Exit back to interface configuration level

fast option gtc

Sets the FAST authentication protocol option to GTC.

fast option md5

Sets the FAST authentication protocol option to MD5.

fast option mschapv2

Sets the FAST authentication protocol option to
MSCHAPv2.

fast provisioning authenticated

Sets the FAST provisioning option to Authenticated.

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands

Lantronix PremierWave 2050, Command Reference Manual

Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands