Lantronix PremierWave 2050 Command Reference Manual Download Page 378

Page: 378 / 428

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

378

prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

write

Stores the current configuration in permanent memory.

password (tunnel-accept-password:3) level commands

clrscrn

Clears the screen.

exit

Exits to the next higher level.

no password

Removes the password so connections will be accepted
unchallenged.

password

<text>

Sets the password required on the network side of the
tunnel to begin a connection.

prompt disable

Inhibits any prompting for password on the network side
of the tunnel.

prompt enable

Sets up so a user on the network side of the tunnel will be
prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

write

Stores the current configuration in permanent memory.

password (tunnel-accept-password:2) level commands

clrscrn

Clears the screen.

exit

Exits to the next higher level.

no password

Removes the password so connections will be accepted
unchallenged.

password

<text>

Sets the password required on the network side of the
tunnel to begin a connection.

prompt disable

Inhibits any prompting for password on the network side
of the tunnel.

prompt enable

Sets up so a user on the network side of the tunnel will be
prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

write

Stores the current configuration in permanent memory.

password (tunnel-accept-password:1) level commands

clrscrn

Clears the screen.

exit

Exits to the next higher level.

no password

Removes the password so connections will be accepted
unchallenged.

password

<text>

Sets the password required on the network side of the
tunnel to begin a connection.

prompt disable

Inhibits any prompting for password on the network side
of the tunnel.

prompt enable

Sets up so a user on the network side of the tunnel will be
prompted for a password.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands

Lantronix PremierWave 2050, Command Reference Manual

Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands