Lantronix PremierWave 2050 Command Reference Manual Download Page 362

Page: 362 / 428

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

362

gap timer

<milliseconds>

Sets the gap timer in milliseconds. If some data has been
received, it will be forwarded after this time since the last
character.

interface rs232

Sets the line interface to RS232.

interface rs485 full-duplex

Sets the line interface to RS485 in full-duplex mode.

interface rs485 half-duplex

Sets the line interface to RS485 in half-duplex mode.

kill session

Kills command mode session on the Line

line

<line>

Enters the line level. <line> = number of the line (serial
port) to be configured.

name

<text>

Sets the name for this line.

no clear line counters

Restores the serial counters to the aggregate values.

no command mode

Disables command mode for the current line.

no command mode signon message

Clears the signon message displayed at boot time and
when entering command mode.

no gap timer

Removes the gap timer, so forwarding depends on the
line speed.

no name

Removes the name of this line.

parity even

Uses a parity bit on the line for even parity.

parity none

Does not use a parity bit on the line.

parity odd

Uses a parity bit on the line for odd parity.

protocol modbus ascii

Applies Modbus ASCII protocol on the line.

protocol modbus rtu

Applies Modbus RTU protocol on the line.

protocol none

Uses no protocol on the line.

protocol tunnel

Applies tunnel protocol on the line.

reassert

Asserts line status with current configured values.

show

Displays the current status.

show command mode

Shows the command mode settings for the current line.

show history

Displays the last 20 commands entered during the current
CLI session.

show line

Displays the current configuration.

show statistics

Shows the line statistics.

state disable

Disables the line so data cannot be sent/received.

state enable

Enables the line so data can be sent/received.

stop bits 1

Uses one stop bit after data on the line.

stop bits 2

Uses two stop bits after data on the line.

terminal

<line>

Enters the configure-terminal level. <line> = number of the
terminal line (serial port) to be configured.

terminal network

Enters the configure-terminal level for the network.

termination disable

Refrains from terminating the line.

termination enable

Enables 120 ohm line termination in RS485 half-duplex
mode.

threshold

<bytes>

Sets the threshold in bytes. After this many bytes are re-
ceived, they are forwarded without delay.

tunnel

<line>

Enters the tunnel level. <line> = number of the tunnel line
(serial port) to be configured.

usb

<line>

Enters the usb level. <line> = number of the line (usb port)

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands

Lantronix PremierWave 2050, Command Reference Manual

Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands