Lantronix PremierWave 2050 Command Reference Manual Download Page 198

Page: 198 / 428

5: Commands and Levels

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference

198

write

Stores the current configuration in permanent memory.

ftp put (config-action-ftp_put:eth0 link state change) level commands

clrscrn

Clears the screen.

connection

<instance>

Enters the next lower level. Specify the instance for the
next lower level.

default mode

Sets default of simultaneous connection mode.

exit

Exits to the next higher level.

mode sequential

Sets sequential mode; will stop after first connection that
goes through.

mode simultaneous

Sets simultaneous mode; will make all possible connec-
tions.

no reminder interval

Clears the FTP Put reminder interval. FTP Put is sent
once only.

reminder interval

<minutes>

Sets the FTP Put reminder interval.

show

Shows the current configuration.

show history

Displays the last 20 commands entered during the current
CLI session.

write

Stores the current configuration in permanent memory.

gateway (config-gateway) level commands

add forwarding rule

<start port>

<end port>

<protocol>

<ip>

Add a forwarding rule without a name.

add forwarding rule

<start port>

<end port>

<target port>

<protocol>

<ingress ip>

<ip>

Add a forwarding rule based on ip address without a
name.

add forwarding rule with name

<name>

<start port>

<end

port>

<protocol>

<ip>

Add a forwarding rule with a name.

add forwarding rule with name

<name>

<start port>

<tar-

get port>

<end port>

<protocol>

<ingress ip>

<ip>

Add a forwarding rule based on ip address with a name.

add ip address filter

<IP address> <action>

Add a IP Address filter.

add mac address filter

<MAC address>

<action>

Add a MAC Address filter.

add route

<network>

<gateway>

<interface>

<metric>

Add a static route without a name.

add route with name

<name>

<network>

<gateway>

<in-

terface>

<metric>

Add a static route with a name.

add virtual ip

<IP address>

<lan ip address>

Add a Virtual IP.

add virtual ip with name

<name>

<IP address>

<lan ip

address>

Add a Virtual IP with name.

clrscrn

Clears the screen.

default default ip address filter policy

Restores the default value of Default IP Address filter pol-
icy (ACCEPT).

default ip address filter policy accept

Sets the Default IP Address filter policy to ACCEPT.

default ip address filter policy drop

Sets the Default IP Address filter policy to DROP.

default operating mode

Restores operating mode to the default value (Disabled).

default router ip address

Restores IP address of router to the default value.

default router ipv6 address

Clears the IPv6 address of router.

default wan interface

Restores preferred WAN interface to the default value.

delete all ip address filters

Deletes all ip address filters.

delete all mac address filters

Deletes all mac address filters.

delete all routes

Deletes all static routes.

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands

Lantronix PremierWave 2050, Command Reference Manual

Search results

Summary of Contents for PremierWave 2050

Reviews:

Related manuals for PremierWave 2050

Brands by name

Popular brands