manualshive.com logo in svg

Lantronix PremierWave 2050, Command Reference Manual, Page: 359 / 428

Share
Download
Lantronix PremierWave 2050 Command Reference Manual Download Page 359

5:  Commands and Levels 

PremierWave® 2050 Enterprise Wi-Fi® IoT Module Command Reference 

359 

default stop bits 

Restores the default of one stop bit. 

default threshold 

Restores the factory default threshold. 

default xoff char 

Restores the default xoff character on this line. 

default xon char 

Restores the default xon character on this line. 

exit 

Exits to the enable level 

flow control hardware 

Uses hardware (RTS/CTS) flow control on the line. 

flow control none 

Does not provide flow control on the line. 

flow control software 

Uses software (xon/xoff characters) flow control on the 
line. 

full duplex termination disabled 

Disables line termination. 

full duplex termination termination on rx 

Sets line termination on Rx only. 

full duplex termination termination on tx 

Sets line termination on Tx only. 

full duplex termination termination on tx and rx 

Sets line termination on Tx and Rx. 

gap timer 

<milliseconds>

 

Sets the gap timer in milliseconds. If some data has been 
received, it will be forwarded after this time since the last 
character. 

interface rs232 

Sets the line interface to RS232. 

interface rs485 full-duplex 

Sets the line interface to RS485 in full-duplex mode. 

interface rs485 half-duplex 

Sets the line interface to RS485 in half-duplex mode. 

kill session 

Kills command mode session on the Line 

line 

<line>

 

Enters the line level. <line> = number of the line (serial 
port) to be configured. 

name 

<text>

 

Sets the name for this line. 

no clear line counters 

Restores the serial counters to the aggregate values. 

no command mode 

Disables command mode for the current line. 

no command mode signon message 

Clears the signon message displayed at boot time and 
when entering command mode. 

no gap timer 

Removes the gap timer, so forwarding depends on the 
line speed. 

no name 

Removes the name of this line. 

parity even 

Uses a parity bit on the line for even parity. 

parity none 

Does not use a parity bit on the line. 

parity odd 

Uses a parity bit on the line for odd parity. 

protocol modbus ascii 

Applies Modbus ASCII protocol on the line. 

protocol modbus rtu 

Applies Modbus RTU protocol on the line. 

protocol none 

Uses no protocol on the line. 

protocol tunnel 

Applies tunnel protocol on the line. 

reassert 

Asserts line status with current configured values. 

show 

Displays the current status. 

show command mode 

Shows the command mode settings for the current line. 

show history 

Displays the last 20 commands entered during the current 
CLI session. 

show line 

Displays the current configuration. 

show statistics 

Shows the line statistics. 

state disable 

Disables the line so data cannot be sent/received. 

Summary of Contents for PremierWave 2050













































































































































































































































































































































































































































Reviews:

No comments