Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 79

Page: 79 / 286

e-MPS

1-65

Printing a Code Job

KM-NET Job Manager

Install the KM-NET Job Manager software from the

Kyocera Mita Digital

Library

CD-ROM supplied with the printer. To do this, from the CD-ROM

Main Menu

, select

Printer Utilities

Install KM-NET Job Manager

Browse through Windows

Start

Programs

KYOCERA MITA

KM-Net

Job Manager

Enter the password for the software.

Job Manager

will start.

Click the

Add printer

icon (below). Select the

Local

Network

port.

If you use the local parallel port to connect to the printer, make sure that
the printer driver is set to print to a local port. To check this out, click the
Details tab of the printer Properties, and note the Print to the following
port setting.

Follow the wizard until the

Select printer

dialog box is reached.

When the printer is found in the

Printer List

, click (highlight) it, then

Finish

Note

Add printer

icon

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Search results

Summary of Contents for 1900N - B/W Laser Printer

Reviews:

Related manuals for 1900N - B/W Laser Printer

Brands by name

Popular brands

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Search results

Summary of Contents for 1900N - B/W Laser Printer

Reviews:

Related manuals for 1900N - B/W Laser Printer

Brands by name

Popular brands