manualshive.com logo in svg

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Share
Download
Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 45

Paper Handling

1-31

Setting the Paper Type in MP Tray

You can automatically select the paper cassette according to the selection 

made by the application software (printer driver). The factory default 

setting is 

Plain

.

This menu does not appears when the option envelope feeder is installed on 

the printer.
For more details about the paper types that can be fed from the MP tray, 

see 

Chapter 2

.

1

Press the 

MENU

 key.

2

Press the   or   key repeatedly until 

Paper Handling >

 appears.

3

Press the 

>

 key.

4

Press the   or   key repeatedly until 

>MP Tray Type

 appears.

5

Press the 

ENTER

 key. A blinking question mark (

?

) appears.

Paper Handling >

>MP Tray Type

  Plain

>MP Tray Type

? Plain

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands