manualshive.com logo in svg

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Share
Download
Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 101

Operating the Storage Device

1-87

Reading Fonts from a CompactFlash Card

If a font (CompactFlash) card is already inserted into the slot when the 

printer is turned on, the fonts are automatically read into the printer. 
To re-read fonts into the printer from a CompactFlash card, proceed as 

follows.

1

Press the 

MENU

 key.

2

Press the   or   key repeatedly until 

Memory Card >

 appears.

3

Press the 

>

 key.

4

Press the   or   key repeatedly until 

>Read fonts

 appears.

5

Press the 

ENTER

 key. A question mark (

?

) appears.

6

Press the 

ENTER

 key. 

Processing

 appears and the reading of fonts 

from the CompactFlash card starts.

7

When the reading of fonts ends, the message display returns to 

>Read fonts

.

8

Press the 

MENU

 key. The message display returns to 

Ready

.

Memory Card

>

>Read fonts

>Read fonts ?

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands