manualshive.com logo in svg

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Share
Download
Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 252

Printing from Windows Applications

3-7

5

To print the first page on the cover, click the 

Front Outside

 check 

box. Note that the 

Front Inside

, 

Back Inside

, and 

Back Outside

 are 

not applicable for model FS-1900.

6

Select the paper source for the cover(s) from the 

Media for Cover

 list 

box. Note that thick paper, colored paper, etc., should be loaded on 

the MP tray.

7

Click the 

OK

 button. The 

Media

 tab is displayed again.

8

Click the 

OK

 button to return to the 

Print

 dialog box.

9

Load the paper you want to use for the cover(s) onto the paper source 

specified in 

step 6

.

10

Click the 

OK

 button to start printing.

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands