manualshive.com logo in svg

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Share
Download
Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 55

Pagination

1-41

Pagination

The items regarding pagination can be made from the operator panel. The 

items that can be set are shown below.
• Emulation
• Font
• Code Set
• Number  of  Copies
• Printing Orientation
• KIR (Kyocera Image Refinement)
• Ecoprint
• Resolution

Emulation

The following procedure allows you to select the printer’s emulation mode.

Changing the Emulation

To change the emulation mode, proceed as follows:

1

Press the 

MENU

 key.

2

Press the   or   key repeatedly until 

Emulation

 appears. One of 

the emulation modes shown below appears, indicating the current 

emulation.

PCL 6

 (default)

KPDL

KPDL (AUTO)

Line Printer

IBM Proprinter

DIABLO 630

EPSON LQ-850

KPDL is the Kyocera’s implementation of the PostScript page 

description language.

3

Press the 

ENTER

 key. A blinking question mark (

?

) appears.

4

Press the   or   key repeatedly until the desired emulation mode 

appears.

Emulation

?PCL 6

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands