Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 198

Page: 198 / 286

Installing Option Units

B-28

Microdrive (Hard Disk)

Insert the Microdrive into its slot on the main circuit board of the printer. If

a Microdrive is installed in the printer, received data can be rasterized and

stored on this Microdrive. This enables high-speed printing of multiple

copies using an electric sort function. Also, you can use the e-MPS

functions. For details, see

e-MPS

on page

1-56

For details of available Microdrives, see your dealer.

Turn off the printer and disconnect the power cord and printer cable.

Remove the two screws from the rear panel.

Pull the main circuit board all the way out of the printer.

Rear Panel

Screws

Main Circuit

Board

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Search results

Summary of Contents for 1900N - B/W Laser Printer

Reviews:

Related manuals for 1900N - B/W Laser Printer

Brands by name

Popular brands

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Search results

Summary of Contents for 1900N - B/W Laser Printer

Reviews:

Related manuals for 1900N - B/W Laser Printer

Brands by name

Popular brands