Kyocera Mita 1900N - B/W Laser Printer Operation Manual Download Page 185

Page: 185 / 286

Installing Option Units

B-15

SO-60 Sorter

Install the option sorter on top of the printer. It is equipped with five sorter

trays, with a capacity of 200 sheets each. There are three modes in which

printouts can be received: the sorter mode, the collator mode, and the mail

box mode (for details about the modes, refer to the

Printer Drivers

Guide

The following installation procedure explains how to install the sorter

when the option paper feeder (PF-60) and duplexer (DU-60) have already

been installed.

Unpack the sorter and place it on its side.

Remove the tapes from the sorter.

Unfold the two attachment legs of the sorter.

Turn off the printer and disconnect the power cord and printer cable.

Tape

Legs

Summary of Contents for 1900N - B/W Laser Printer































































































































































































































































































Search results

Summary of Contents for 1900N - B/W Laser Printer

Reviews:

Related manuals for 1900N - B/W Laser Printer

Brands by name

Popular brands

Kyocera Mita 1900N - B/W Laser Printer, Operation Manual

Search results

Summary of Contents for 1900N - B/W Laser Printer

Reviews:

Related manuals for 1900N - B/W Laser Printer

Brands by name

Popular brands