Kohler CH980 Service Manual Download Page 73

Page: 73 / 124

8.6

Section 8
Disassembly

Figure 8-20. Disconnecting Hoses From Oil Cooler.

Remove Oil Filter Housing and Oil Filter
Adapter

1. Remove the screw securing the oil filter housing

and individual O-Rings to the adapter. Carefully
separate the parts. See Figure 8-21.

NOTE

: Further disassembly of the oil filter

housing assembly is not required unless
individual servicing must be performed.
Follow substeps a, b, and c.

Figure 8-23. Disassembled Cup and Spring.

Remove Oil Cooler

1. Remove the two oil cooler mounting screws. Do

not lose any washers (if used). See Figure 8-19.

Figure 8-21. Removing Oil Filter Housing From
Adapter.

Perform the following only if the oil filter housing
assembly requires individual servicing.

a. Remove the nipple from the cup and oil filter

housing. See Figure 8-22.

Figure 8-22. Removing Nipple.

b. Remove the oil filter cup and spring from

housing. See Figure 8-23.

Figure 8-19. Removing Oil Cooler Mounting
Screws.

2. Loosen the clamps and disconnect each of the

hoses from the oil cooler. See Figure 8-20.

NOTE

: New clamps are recommended any time

disassembly is performed, or if clamps
have been loosened (expanded) several
times.

Housing
Mounting
Screw

Nipple

Spring

Cup

Nipple

Housing

Summary of Contents for CH980





























































































































Search results

Summary of Contents for CH980

Reviews:

Related manuals for CH980

Brands by name

Popular brands

Kohler CH980, Service Manual

Search results

Summary of Contents for CH980

Reviews:

Related manuals for CH980

Brands by name

Popular brands