Kohler CH980 Service Manual Download Page 70

Page: 70 / 124

8.3

Section 8

Disassembly

Remove Electric Starter Motor

1. Disconnect the leads from the starter.

2. Remove the two hex flange screws and starter.

See Figure 8-7.

Figure 8-10. Removing Air Cleaner Assembly.

Figure 8-7. Removing Electric Starter.

Remove Air Cleaner Assembly

1. Disconnect the breather hose from the air cleaner,

and the formed vent hose from the vent port on
the carburetor.

2. Remove the four hex flange nuts, ground lead,

and choke return spring bracket from the
mounting studs. See Figure 8-8.

Figure 8-9. Mounting Screws.

4. Remove the air cleaner as an assembly from the

engine. See Figure 8-10.

Figure 8-8. Air Cleaner Mounting Details.

Mounting

Nuts

Bracket

Breather
Hose

Vent Hose

Mounting
Screws

3. Remove the two screws securing the air cleaner

and main control bracket to the intake manifold
bosses. See Figure 8-9.

Mounting
Screws

Summary of Contents for CH980





























































































































Search results

Summary of Contents for CH980

Reviews:

Related manuals for CH980

Brands by name

Popular brands

Kohler CH980, Service Manual

Search results

Summary of Contents for CH980

Reviews:

Related manuals for CH980

Brands by name

Popular brands